Production Details:
Designed to be positioned either side of any Hornby
point, this surface mounted point motor allows for the
convenient electrical operation of points. Can be used
with the Hornby R8216 Digital Point / Accessory decoder
or for DC analogue operation, the R044 Lever Switch. May
not be suitable for use with points which are
incorporated into certain track configurations.
Production Details:
Powerful solenoid point
motor for new model Hornby points that have the sliding
bar mechanism. May be mounted above or below the
baseboard (requires Point Motor Housing R8015 for
mounting above). Comes supplied with metal extension arm
for mounting motor underneath the baseboard. Powered
from the accessory power output on your controller (or
other 16v AC supply). Requires 'passing contact' lever
switch R044 (not included).
Production Details:
Provides a base to mount
Point Motor R8014 above the baseboard, with a model
trackside hut to conceal it. Comes with variable
extension arm that allows you to position the motor at
different distances from the track, on either side of
the point. The base of the housing may also be used to
mount the motor under the baseboard.
Production Details:
The Hornby “Elite”
Digital Controller is more than capable of answering the
needs of most railway layouts – twin control with press
dial function, 17 button alpha numeric keyboard, wide
function LCD screen, four amp power, as well as having
the capabilities of registering 254 locomotive addresses
as well as 255 solenoid powered accessory addresses
(including point control), plus a USB portal for linking
to a Personal Computer.
The Hornby “Elite” unit
is an ideal way for the enthusiast to take their train
control to a new and advanced level.
Production Details:
The future of model
railway control is here with the latest and best Hornby
Digital Command Control System. The new Hornby system
differs from the conventional type of 12v controllers in
as much that it is the individual locomotives that are
controlled internally rather than the controlling a
locomotive's speed and direction by varying the current
to the track.
The Hornby Select Digital
Controller is the perfect way to enter the digital world
of model railways. The Select is capable of having
control of over 60 locomotives and, providing power is
available, run at any one time, 10 of them. The Select
can also operate 40 accessories including point motors.
Production Details:
Up to eight of these
units can be connected to a single Select or Elite
Digital controller allowing for independent management
of a further eight locomotives providing power is
available. Note:
It is not necessary to connect a power pack to the
Walkabout when used in this way and thus one is not
supplied. Instead an RJ12 connection cable is included
in this pack.
Production Details:
This
locomotive decoder is suitable for any 'DCC Ready'
locomotive, and can be easily programmed for use with
Hornby's Select or Elite DCC Units. This Decoder has
load compression where the motors rotational speed is
controlled and not simply the voltage, separate
acceleration and deceleration, 14 28 or128 speed steps,
Main track programming Four on-off function (two
functions are dedicated to head and tail lights), Able
to operate on standard DC systems, and motor overload
protection. With NMRA RP-9.1.1 /
NEW652 medium plug.
Product Code: R8215
- This model has been replaced by R8249
Production Details:
This
locomotive decoder is suitable for any 'DCC Ready'
locomotive, and can be easily programmed for use with
Hornby's Select or Elite DCC Units. This Decoder has
load compression where the motors rotational speed is
controlled and not simply the voltage, separate
acceleration and deceleration, 14 28 or128 speed steps,
Main track programming Four on-off function (two
functions are dedicated to head and tail lights), Able
to operate on standard DC systems, and motor overload
protection
Lenz - Standard
Decoder
(3 Function output A, B, C)
Product Code:
L10231
Product information:
(replacement for the LE1000) The DIGITAL plus
STANDARD locomotive decoder is suitable for all DC
locomotives with continuous current draw of 1.0 Amp. or
less. Super smooth and silent high frequency back-emf
motor control. Selectable for operation with 14/27, or
28/128 speed steps. Operation on conventional DC layouts
is possible or can be disabled. Motor output = 1A
continuous, 1.8A max, > 5 A stall. Three function
outputs rated at 100mA each with advanced function
mapping. Directional or independent lighting with
dimming and special effects.
Product information:
The DIGITAL plus SILVER locomotive decoder is suitable
for all DC locomotives with continuous current draw of
1.0 Amp. or less. Super smooth and silent high frequency
back-emf motor control. Asymmetrical DCC support
including directional stopping. Selectable for operation
with 14/27, or 28/128 speed steps. Operation on
conventional DC layouts is possible or can be disabled.
Motor output = 1A continuous, 1.8A max, > 5 A stall.
Four function outputs rated at 100mA each with
advanced function mapping. Directional or independent
lighting with dimming and special effects. Size: L 23mm
x W 16.6mm x H 2.9mm
Product information:
The DIGITAL plus SILVER DIRECT locomotive
decoder has a built in NMRA 8 pin plug and is suitable
for all DC locomotives with continuous current draw of
1.0 Amp. or less with such a socket. Super smooth and
silent high frequency back-emf motor control.
Asymmetrical DCC support including directional stopping.
Selectable for operation with 14/27, or 28/128 speed
steps. Operation on conventional DC layouts is possible
or can be disabled. Motor output = 1A continuous, 1.8A
max, > 5 A stall. Four function outputs rated at
100mA each with advanced function mapping. Directional
or independent lighting with dimming and special
effects. Size: L 23mm x W 16.6mm x H 2.9mm
Product information:
The DIGITAL plus SILVER 21 locomotive decoder has a
built in NMRA 21 pin plug and is suitable for all DC
locomotives with continuous current draw of 1.0 Amp. or
less. with such a socket. Super smooth and silent high
frequency back-emf motor control. Asymmetrical DCC
support including directional stopping. Selectable for
operation with 14/27, or 28/128 speed steps. Operation
on conventional DC layouts is possible or can be
disabled. Motor output = 1A continuous, 1.8A max, > 5 A
stall. Four function outputs rated at 100mA each
with advanced function mapping. Directional or
independent lighting with dimming and special effects.
Size: L 23mm x W 16.6mm x H 2.9mm
Product information:
The DIGITAL plus Gold locomotive decoder is suitable
for all DC locomotives with continuous current draw of
1.0 Amp. or less. Super smooth and silent high frequency
back-emf motor control. Supports the industry proposed
enhancements to the NMRA DCC Bidirectional data
communication RPs USP with optional power module for
operation on dirty track. Asymmetrical DCC support
including directional stopping. Selectable for operation
with 14/27, or 28/128 speed steps. Operation on
conventional DC layouts is possible or can be disabled.
Motor output = 1A continuous, 1.8A max, > 5 A stall.
Four function outputs rated at 200mA each with
advanced function mapping. Directional or independent
lighting with dimming and special effects. Size: L 23.0
mm x W 16.5 mm x H 6.5 mm
Product information:
The DIGITAL plus LS150 turnout decoder provides cost
effective turnout control for up to 6 independent
turnouts. Suitable for twin-coil snap action switch
machines. Suitable for motorized switch machines. High
current provision to support Peco and Atlas switch
machines. The 6 turnout addresses can be sequential or
up to 6 user selected addresses. Control using separate
push-buttons possible. Configuring the LS150 does not
require a separate programming track and the parameters
can be changed at any time in the future even after
installation.
Hornby - Accessory
decoder for 4 points / turnouts
Product Code: R8216
- Replaced by R8247
Production Details:
This
point decoder is suitable for fitting to any point, and
can be easily programmed for operation by Hornby's
Select or Elite DCC Units. The Hornby point motor
decoder incorporates a capacitor discharge unit can
accommodate the connection of up to four point motors or
other accessories that function using a solenoid.
This pack includes a Point
Decoder, decoder to track link wire and a screw driver
and screws.
Production Details:
4 amp
transformer which is capable of providing enough power
to run approximately eight locomotives at any one time.
Can be used as a replacement
for the 1 amp transformer supplied with the select
unit
to allow the control of more locomotives simultaneously.
Production Details:
DCC control works best when the whole layout is "live".
Hornby points are self isolating so therefore need 2 DCC
point clips to be fitted to the point to allow the power
to flow down both routes. 20 clips per pack
Hornby RJ-12 Lead
(To connect a select to an elite) 3 Metres
Product Code: R8236
Production Details:
RJ-12 cables are used to connect DCC controllers
together using the express net socket. This cable will
allow you to connect a Hornby select as an extra
controller to a Hornby elite.
Production Details:
To be used
when track configurations such as a reverse loop or
triangle permanent way sections are used in a circuit.
The Hornby Reverse Loop module controls the polarity of
the track so that locomotives running around these
sections can do so uninterrupted without the use of
switches and complicated wiring. Can only be used with
the Hornby Digital units.
Production Details:
Designed to divert power from one
circuit to another - eg. with R406 coloured light
signals to switch from red to green and back again. It
may also be used to switch power from one section of
track to another and is the switch you use to operate
turntable R070.
Production Details:Controls
the direction and speed of one locomotive. Input is 16v
AC from the R964 mains transformer (not supplied, see
above). Output is 0-12v DC to the track, plus
non-variable 16v AC output for power-switched points,
signals and other accessories. Supplied fitted with
760mm lead to Power Connecting Clip.
Production Details: A
complete transformer and speed control unit with
built-in control for two separate trains, extendable to
four trains by adding slave control units (HM2000+).
Power output is two Amps, with compensation to
regularise speed under varying conditions of load.
'Positive off' rotary speed control cuts all power when
the control knob is turned to Zero. Features include
forward and reverse switch, plus LED indicators for
mains supply and output power. Outputs include
non-variable AC and DC power for point motors and other
powered accessories.
Production Details:2
Aspect Red/Green Light Signal. This signal
requires a on-on switch to operate or DCC
Accessory decoder. Functions: Built-in Circuit Protection, Fading in - Fading out
adjustment, Plug & Play interface circuit board, LED’s for low power
consumption and reliability. No Soldering required. Signal
identification numbers/lettering, ladder, and ladder safety ring included.
TrainTronics - 2 Aspect Yellow / Green
Light Signal
Product Code: TT103
Production Details:2
Aspect Red/Green Light Signal. This signal
requires a on-on switch to operate or DCC
Accessory decoder. Functions: Built-in Circuit Protection, Fading in - Fading out
adjustment, Plug & Play interface circuit board, LED’s for low power
consumption and reliability. No Soldering required. Signal
identification numbers/lettering, ladder, and ladder safety ring included.
TrainTronics - 3 Aspect Green / Yellow /
Red Light Signal
Product Code: TT104
Production Details:2
Aspect Red/Green Light Signal. This signal
requires a on-on switch to operate or DCC
Accessory decoder. Functions: Built-in Circuit Protection, Fading in - Fading out
adjustment, Plug & Play interface circuit board, LED’s for low power
consumption and reliability. No Soldering required. Signal
identification numbers/lettering, ladder, and ladder safety ring included.
Hornby Colour
Light Signal
Product Code: R406
Production Details:
Switches from red to green
and back again. Powered from the accessory power output
on your controller (or other 16v AC supply). Operated by
'on-on' lever switch R046 (not included).
Production Details:
This junction home signal is for manual operation only.
Height 172mm. This signal represents the type of signal
used on the approach to points. The taller signal
controls the main line.
Production Details:
This junction distant signal is for manual operation
only. Height 172mm. This signal represents the type of
signal used on the approach to points. The taller
signals controls the main line. The yellow arms signify
"distant" or "caution", and are seen prior to signals
with red arms.
Production Details:
This signal may be fitted
for remote operation by adding point motor R664 and
'passing contact' lever switch R044 (not included). They
may also be operated by hand. Height: 121mm
Production Details:
This signal may be fitted for remote operation by
adding point motor R664 and 'passing contact' lever
switch R044 (not included). They may also be operated by
hand. Height: 121mm
All product information is
correct when entered in to the website and comes from Hornby.
This information is subject to change without notification by
Hornby. Please check the Hornby website for the latest
information at
www.hornby.co.uk
