Railway Track - Hornby Model Railway Points

Hornby Left-Hand Point

Product Code: R8072 (HT8302)

Production Details:

Length: 168mm Arc: 22.5°. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Right-Hand Point

Product Code: R8073

Production Details:

Length: 168mm, Arc: 22.5°. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Left-Hand Express Point

Product Code: R8077

Production Details:

Arcs 11.25°, Length 245mm. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Right-Hand Express Point

Product Code: R8078

Production Details:

Arcs 11.25°, Length 245mm. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Left-Hand Curve Point

Product Code: R8074

Production Details:

Arcs 22.5° & 33.75°. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Right-Hand Curve Point

Product Code: R8075

Production Details:

Arcs 22.5° & 33.75°. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby Y Point

Product Code: R8076

Production Details:

Arcs 22.5° & 33.75°. Hornby points are supplied for operation by hand. They may be converted to remote control electric operation by using a 'point motor'.

Hornby - Accessory Decoder with 4 Outputs

Product Code: R8247

Production Details:

This Accessory decoder is suitable for fitting to any point, and can be easily programmed for operation by Hornby's Select or Elite DCC Units. The four outputs are factory set for the operation of solenoid (point) motors, however, by adjusting the CV settings of each output a graduation of varying "bursts" of current up to a constant current (turntable motor operation, lighting, etc.) can be obtained for each individual output.

This pack includes a Point Decoder, decoder to track link wire and a screw driver and screws. Replacement for R8216.

Hornby DCC Electronic Point Clips

Product Code: R8232

Production Details:

DCC control works best when the whole layout is "live". Hornby points are self isolating so therefore need 2 DCC point clips to be fitted to the point to allow the power to flow down both routes. 20 clips per pack

Hornby Passing Contact Switch

(for point motors)

Product Code: R044

Production Details:

Supplies the brief pulse of current that a point motor requires. Supplied with connecting wires.

Hornby Surface Mounted Point Motor

Product Code: R8243

(Pre-Order - Stock Due August 2020)

Production Details:

Designed to be positioned either side of any Hornby point, this surface mounted point motor allows for the convenient electrical operation of points. Can be used with the Hornby R8216 Digital Point / Accessory decoder or for DC analogue operation, the R044 Lever Switch. May not be suitable for use with points which are incorporated into certain track configurations.

Hornby Point Motor

Product Code: R8014

Production Details:

Powerful solenoid point motor for new model Hornby points that have the sliding bar mechanism. May be mounted above or below the baseboard (requires Point Motor Housing R8015 for mounting above). Comes supplied with metal extension arm for mounting motor underneath the baseboard. Powered from the accessory power output on your controller (or other 16v AC supply). Requires 'passing contact' lever switch R044 (not included). Does not include below board mounting screws.

Hornby Point Motor Housing

Product Code: R8015

Production Details:

Provides a base to mount Point Motor R8014 above the baseboard, with a model trackside hut to conceal it. Comes with variable extension arm that allows you to position the motor at different distances from the track, on either side of the point. The base of the housing may also be used to mount the motor under the baseboard.

SEEP Point Motor with Built-In Polarity Switch

Product Code: PM1

Production Details:

Seep Point Motors have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-1 is our best selling point motor and has a built in changeover switch to operate accessories or change frog polarity.

SEEP Point Motor - No Switch

Product Code: PM2

Production Details:

Seep Point Motors have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-2 is our standard point motor with no changeover switch.

SEEP Point Motor with Latching Mechanism

Product Code: PM4

Production Details:

Seep Point Motors have the advantage of being easy to fix under the baseboard. requiring only a small slot to operate the point. The PM-4 is a self-latching point motor, ideal for use with hand-made points, and also includes a changeover switch for operating accessories or changing frog polarity.

Gaugemaster Surface Mounted Point Motor

Product Code: GMC-PM20

Production Details:

Designed with easy installation in mind, PM20 is placed parallel to your point-work and operates equally well orientated either way. PM20 works well with all popular modelling scales, and with the leading brands of track in the UK.
The magnetic coils are high-efficiency for reliable operation, needing much less current than most other brands. PM20 also has a plug-in harness that is very easy to use. Mounting screws are included.

SEEP Classic Solenoid Point Motor

Product Code: GMC-PM10 / GMC-BPPM10 (Pack of 5)

Production Details:

This Point Motor has been created to work with the leading brands of track in the United Kingdom. Designed with easy installation in mind, it has a built inreversible mounting plate (with adjustment slots and holes), robust, plated metalwork and fibreglass PCBs for longer life.
The PM10’s magnetic coils are high efficiency for reliable operation, needing much less current than other brands. PM10 also has easy to use “solder-free” screw terminals. We have included mounting screws and a throw-bar extension.
Click Here To view the instructions for the PM-10

Gaugemaster Capacitor Discharge Unit (CDU)

Product Code: CDU

Production Details:

For operating heavy duty point motors. The unit stores up power in capacitors and when a point motor is actuated, discharges in one big punch giving the point motor a firm and positive switching action. Connected to points via switches or probe and studs. Prevents burnt out motors.
Input: 16v to 24v A.C. at a maximum of 2.5 amps Gaugemaster T1 for Hornby/ Peco/ Seep point motors or T3 for 24v applications.